Whatsapp&Wechat

+15724025188

Email

What Is Silicone? An Industrial Material Guide

Silicone is a family of synthetic polymers built around silicon-oxygen bonds. It can be formulated as fluids, gels, resins or flexible elastomers. For industrial parts, the correct choice depends on grade, cure chemistry, hardness, geometry, exposure and finished-article evidence.

Silicone, Silicon and Silica Are Different Materials

The similar names often create specification errors, but silicone, silicon and silica describe different substances.

Silicon is the chemical element Si. In industrial supply chains, it appears in semiconductor materials, metal alloys and as a raw material for producing silicon-based compounds. It is not the soft, elastic substance used for flexible seals or tubing.

Silica is silicon dioxide, commonly written as SiO₂. Quartz and sand contain silica, which can serve as an upstream source for silicon production. Finely divided silica is also used as a reinforcing filler in many elastomer formulations.

Silicone refers to a broad family of synthetic polymers with alternating silicon and oxygen atoms in the main chain and organic groups attached to the silicon atoms. Depending on its formulation and molecular structure, it may become a fluid, grease, gel, resin, sealant or cured elastomer. This silicon-oxygen backbone is a defining feature of the polymer family

For an industrial rubber component, specifying only “silicon” is usually an error. A workable drawing or RFQ should identify silicone rubber and then define the grade, hardness, cure system, color, dimensions and operating condition

Author

blog writer

Hi, I’m David Xu , Focus on the rubber products industry for 20 years.  I design customized rubber products solutions,i brings practical insights into material selection,quality control,and application solutions.  I’m here to share industry knowledge and best practices for customers and partners.

Specification Interpretation Table

Term Found in a Drawing or RFQLikely MeaningProcurement RiskRequired Action
SiliconElemental silicon or a silicon-containing industrial materialMay direct the inquiry to semiconductor, alloy or chemical suppliersAsk whether the intended material is silicone rubber
SilicaSilicon dioxide in mineral or filler formDoes not define the base polymer of the componentClarify whether silica is a filler, raw material or separate product
SiliconeA broad polymer familyDoes not identify physical form, grade or cure chemistryDefine whether the project needs fluid, gel, resin, sealant or elastomer
Silicone rubberA curable elastomeric formulationStill leaves hardness, process and service performance unresolvedAdd grade, hardness, cure system, dimensions, environment and acceptance criteria
Silicone partA finished article made from a silicone formulationMay conceal differences in molding, extrusion, post-curing and testingRequest the drawing, production method, material declaration and inspection plan

Why Molecular Structure Changes Performance?

Silicone cannot be understood from the name alone. Its behavior comes from the polymer structure, the organic groups attached to it, the reinforcing system and the way the compound is cured.

Polydimethylsiloxane, or PDMS, is a common example. Its backbone contains repeating silicon-oxygen units, while methyl groups are attached to the silicon atoms. Other organic groups, including vinyl or phenyl groups, may be introduced to support particular curing reactions or modify specific characteristics.

The siloxane chain is more flexible than the carbon-based backbone found in many conventional organic polymers. At the same time, the Si-O bond has relatively high bond energy. These structural characteristics help properly formulated grades remain flexible across a broad temperature range and withstand weathering better than many general-purpose elastomers. Molecular structure alone, however, does not guarantee the performance of a finished component.

Before curing, the polymer may be supplied as a pourable liquid or a high-consistency compound. Crosslinking connects separate chains into a three-dimensional network, turning the uncured formulation into an elastic solid. Fillers, pigments, catalysts, stabilizers and other additives are incorporated to control processing and final behavior.

Two compounds may both be described as silicone rubber yet differ significantly in viscosity, hardness, tear resistance, compression behavior, color stability or suitability for a particular production method. Approval should therefore be based on a defined formulation and validated component, not on the polymer name alone

From Silica to a Processable Base

Producing the base polymer is different from manufacturing a gasket, tube, grommet or other finished article. The upstream chemical process creates silicone raw materials; molding, extrusion and secondary operations later convert a selected compound into the required geometry.

A simplified production route includes five stages:

1.Producing silicon metal

 Silica-rich raw material is processed at high temperature to obtain elemental silicon. The resulting material is refined and prepared for chemical conversion.

2.Creating chlorosilane intermediates

 Finely divided silicon reacts with methyl chloride under controlled conditions. This reaction produces a mixture of methylchlorosilanes rather than a ready-to-use elastomer

3.Separating the reaction products

 Distillation isolates the required chlorosilane fractions. This stage matters because different intermediates lead to different downstream structures and product families.

4.Forming siloxane units and polymer chains

 Selected chlorosilanes undergo hydrolysis and condensation. Further polymerization or equilibration controls chain length, molecular distribution and the form of the resulting polymer.

5.Preparing a usable formulation

The base polymer is combined with reinforcing fillers, processing aids, pigments, crosslinking ingredients and other additives. The formulation may then be supplied as liquid silicone rubber, high-consistency rubber or another silicone system.

This sequence is intentionally simplified. Actual chemistry, equipment and process controls vary by producer and product family. It nevertheless explains why silica, silicon metal, silicone polymer and silicone rubber compound describe different stages rather than interchangeable material

Industrial buyers normally do not need to specify the upstream synthesis route. They do need traceable compound identification, an appropriate cure system and evidence that the selected formulation can meet the component’s dimensional and functional requirements

One Polymer Family, Many Commercial Forms

The term silicone covers multiple product families with different physical forms and functions. Some are designed to flow, lubricate, coat, bond or encapsulate. Others are formulated to cure into flexible elastomeric components.

This distinction should be established before comparing hardness, temperature capability or manufacturing cost. A silicone fluid cannot be evaluated as though it were a molded seal, while a room-temperature sealant should not be assumed to meet the dimensional controls of an injection-molded component.

For custom rubber products, the most relevant categories are usually liquid silicone rubber, high-consistency rubber and selected room-temperature-vulcanizing systems. Their supply condition, mixing requirements, curing method and practical manufacturing routes are differen

Silicone Form and Procurement Map

Silicone Family or Form

Typical Supply Condition

Common Function

Main Procurement Question

Silicone fluid

Pourable liquid with viscosity determined by molecular weight and formulation

Lubrication, heat-transfer media, release control or formulation ingredient

Is the fluid itself the product, or is it an ingredient in another system?

Silicone grease

Thickened, non-flowing or semi-flowing material

Lubrication, sealing assistance or electrical protection

What temperature, contact materials and migration limits apply?

Silicone gel

Soft, lightly crosslinked system

Cushioning, encapsulation or protection of sensitive assemblies

What softness, tack, dielectric behavior and rework requirements must be controlled?

Silicone resin

Highly crosslinked coating or binder system

Protective coatings, electrical insulation or heat-resistant finishes

Is flexibility required, or is a rigid coating acceptable?

RTV silicone

One- or two-part system designed to cure near room temperature

Sealing, bonding, encapsulation, casting or low-volume fabrication

What cure chemistry, depth, environment and production rate are acceptable?

Liquid silicone rubber

Pumpable two-part elastomer, commonly processed through metering and injection equipment

Precise molded components, complex shapes and high-volume production

Can the tooling, metering system and mold design control flash, venting and cure?

High-consistency rubber

High-viscosity compound handled as a solid or putty-like material

Compression-molded parts, extruded profiles and silicone rubber tubing

Which molding or extrusion route matches the geometry and tolerance requirements?

Typical Properties and Engineering Ranges

Silicone rubber is selected for more than flexibility. Its value lies in maintaining useful mechanical and electrical behavior under temperature change, outdoor exposure and electrically demanding conditions. The figures below are practical screening ranges, not universal specification limits. A supplier’s technical datasheet and finished-part testing must define the approved values.

Temperature Capability

For many industrial silicone rubber compounds, -60°C to 240°C can be used as an initial material-screening range. The allowable exposure depends on time, load, surrounding media, part geometry and the property that must be retained.

Continuous operation is often rated more conservatively than short peak exposure. A component that survives a brief period at 240°C may still harden, lose elongation or develop excessive compression set during prolonged service at the same temperature. Specialty formulations can extend low- or high-temperature capability, but they require grade-specific aging data.

Temperature evaluation should therefore define:

Minimum operating and cold-start temperature

Normal continuous temperature

Peak value and exposure duration

Compression, tension or movement during heating

Air, steam, oil, chemical or enclosed-service conditions

Permitted changes in hardness, tensile strength and elongation

Wacker describes long-term thermal resistance around -50°C to 180°C for general RTV elastomers, with specialty grades extending below -100°C or toward 270°C. It also notes that service duration and peak loading must be considered separately

Hardness Range

A common working range for molded or extruded silicone components is approximately 30 to 70 Shore A. Within this range, the compound can be adjusted for sealing, flexibility, insertion force, wall stability and handling during assembly.

Special formulations may extend the available range to roughly 20 to 90 Shore A, although the endpoints introduce additional design considerations:

Around 20 Shore A, thin walls may deform easily, handling can become difficult and dimensional inspection requires controlled support.

Between 30 and 50 Shore A, the cured article generally offers greater flexibility and lower assembly force.

Between 50 and 70 Shore A, higher stiffness can improve shape retention but may increase insertion or sealing force.

Near 80 or 90 Shore A, the elastomer becomes much less compliant; designers should verify whether it can still accommodate tolerances and maintain contact pressure.

Hardness alone does not define sealing performance. Two 50 Shore A compounds may differ in modulus, compression set, tear strength and stress relaxation

Mechanical Property Window

Typical silicone elastomers can be formulated across broad mechanical ranges. Depending on grade and test method, initial screening values may include

Property

Typical Engineering Range

Why It Matters

Hardness

30–70 Shore A for many standard components; approximately 20–90 Shore A with specialized formulations

Influences flexibility, insertion force, sealing contact and dimensional stability

Tensile strength

Approximately 5–10 MPa for many reinforced grades

Indicates resistance to pulling but does not predict notch or cut growth

Elongation at break

Commonly 200–700%; broader specialty ranges may be available

Supports stretching and assembly movement but must be assessed after aging

Tear strength

Approximately 10–40 N/mm for many engineered grades

Important for thin lips, holes, sharp transitions and parts removed from tooling

Compression set

Highly dependent on time, temperature, deflection and cure condition

Affects the ability of a gasket or static seal to maintain contact pressure

These values should not be copied directly into a drawing without identifying the test standard, specimen geometry, cure condition and acceptance range

Electrical Insulation Performance

Many insulating silicone rubber compounds have high volume resistivity, useful dielectric strength and comparatively stable electrical behavior across temperature and frequency changes. Published product data commonly show:

Volume resistivity: approximately 10¹⁴ to 10¹⁶ Ω·cm for insulating grades

Dielectric strength: often around 20 to 30 kV/mm, depending on formulation, specimen thickness and test method

Dielectric constant: commonly in the low single digits for unfilled or conventionally filled insulating compounds

Low dielectric loss: available in formulations intended for electrical protection and encapsulation

For example, Dow lists volume resistivity of 2.9 × 10¹⁴ Ω·cm and dielectric strength of approximately 17.7 kV/mm for one cured encapsulating elastomer. A separate flame-resistant silicone base is reported at 1 × 10¹⁵ to 5 × 10¹⁶ Ω·cm with dielectric strength between 20 and 40 kV/mm. These examples demonstrate the variation between products rather than establishing one value for all silicone rubber

Silicone rubber can also provide useful corona, arc, tracking and erosion resistance in appropriately formulated high-voltage grades. These characteristics make it suitable for insulators, cable accessories, protective boots, connector seals and electrical barriers. They are not automatic properties of every compound. Pigments, conductive fillers, contamination, moisture, wall thickness, creepage distance and surface condition can alter the result

Weathering and Environmental Stability

Properly formulated silicone elastomers generally resist ozone, ultraviolet exposure and oxidation better than many general-purpose rubbers. Their hydrophobic surface can also support electrical performance in wet outdoor environments.

Environmental resistance does not mean universal chemical compatibility. Fuels, concentrated acids or alkalis, solvents, hot oils and pressurized steam may cause swelling, softening, loss of strength or other changes. Exposure testing should use the actual fluid, concentration, temperature and duration

Engineering Screening Table

Project Condition

Suitable Starting Point

Evidence Required Before Approval

Service between -60°C and 200°C

General heat-resistant silicone grade

Thermal-aging results at actual time and load

Repeated exposure approaching 240°C

High-temperature formulation

Retained hardness, tensile strength, elongation and compression set

Soft sealing or easy assembly

Approximately 20–40 Shore A

Dimensional stability, tear strength and assembly trial

General molded seal or grommet

Approximately 40–70 Shore A

Compression behavior, tolerance and functional test

Rigid elastomeric support

Approximately 70–90 Shore A specialty grade

Contact pressure, flexibility and stress-relaxation assessment

Electrical insulation

Insulating or high-voltage compound

Volume resistivity, dielectric strength, tracking and environmental tests

Outdoor high-voltage use

Hydrophobic, tracking-resistant formulation

Wet electrical performance, corona/arc exposure and aging evidenc

Limits and Common Failure Risks

Silicone rubber is not the best choice for every flexible component. Broad temperature capability and electrical stability can be valuable, but they do not compensate for unsuitable fluid exposure, poor geometry or an incorrect production grade

Tear and Cut Sensitivity

Standard silicone compounds generally have lower tear and cut-growth resistance than tougher elastomers such as polyurethane or some reinforced natural-rubber formulations. A small nick created during trimming, assembly or service can become a failure origin.

Risk increases around:

Sharp internal corners

Thin sealing lips

Pierced holes and narrow slots

Abrupt wall-thickness transitions

Rough mating surfaces

Excessive stretching during installation

Poorly controlled flash trimming

Higher-tear grades may reduce the risk, but geometry remains important. Increasing the radius, removing sharp edges and controlling the assembly path can be more effective than specifying tensile strength alone

Abrasion and Dynamic Wear

General-purpose silicone rubber is not normally the first choice for continuous sliding, scraping or abrasive contact. Repeated movement against a rough shaft or housing may damage the surface even when temperature and weather resistance are acceptable.

Dynamic seals should be evaluated for contact pressure, surface finish, lubrication, movement speed, stroke length and generated heat. Where wear is the dominant failure mode, another elastomer or a low-friction interface may provide a better starting point.

Parker describes silicone elastomers as having relatively low tensile strength, poor tear strength and limited wear resistance compared with several other sealing material

Gas and Vapor Permeability

Silicone rubber is relatively permeable to gases. This characteristic can be useful in breathable membranes, but it creates risk in pneumatic sealing, vacuum systems and tubing that must limit gas loss or vapor transmission.

Permeation is different from leakage through a gap. A component may have no visible defect and still allow molecules to pass through the elastomer. The rate is affected by:

Gas type

Pressure differential

Wall thickness

Exposed surface area

Temperature

Compound formulation

Required service duration

Fuels, Oils and Solvents

Standard VMQ silicone may swell in hydrocarbon fuels, aromatic solvents, ketones, esters and some oils. Swelling can change dimensions, reduce strength, soften the component or increase compression set.

Chemical compatibility should be evaluated with the exact fluid rather than a general description such as oil resistant. The test plan should define:

Fluid name and formulation

Concentration

Operating and peak temperatures

Immersion or intermittent-contact time

Pressure and mechanical load

Allowable volume, mass and hardness change

Required retained tensile or sealing performance

When low-temperature flexibility and improved fuel resistance are both needed, fluorosilicone may be considered. It is a separate material family and should not be presented as a universal replacement for standard VMQ

Compression Set and Stress Relaxation

A silicone gasket can pass an initial leakage test but gradually lose sealing force. Compression set measures the permanent deformation remaining after a compressed specimen is released. Stress relaxation describes the reduction in force while the component remains compressed.

The two properties are related to long-term sealing but are not interchangeable. Results depend on:

Compound and cure system

Post-cure condition

Compression percentage

Test time and temperature

Cross-sectional geometry

Constraint inside the assembly

Contact with fluids

Hardness alone cannot predict either behavior. A high-temperature seal should be tested after representative aging while compressed in a fixture or actual assembly

Bonding, Printing and Coating

Bonding, Printing and Coating

The low surface energy that supports release behavior can also make silicone difficult to bond or print. An adhesive that works on metal, EPDM or plastic may not adhere reliably to a cured silicone surface.

Depending on the design, successful bonding may require:

A silicone-compatible adhesive

Plasma, corona or chemical surface treatment

Primer

Controlled cleaning

Mechanical interlocking

Insert molding or overmolding with a validated substrate

Surface treatment effectiveness can decline with time. Bonded samples should therefore represent the actual cleaning, treatment, storage and assembly sequence

Extractables, Volatiles and Silicone Transfer

Extractables, Volatiles and Silicone Transfer

Some formulations may release low-molecular-weight siloxanes, processing residues or other extractable substances. These may matter in optical, electronic, painted, adhesive-bonded or highly controlled applications.

Possible effects include surface contamination, reduced adhesion, optical deposits or interference with nearby processes. Low-volatility or specially controlled grades may be required, followed by suitable post-curing and cleanliness verification.

High Temperature Does Not Mean Unlimited Life

A published upper temperature is not a guaranteed service-life value. Extended heat exposure can increase hardness, reduce elongation and weaken thin or highly strained areas. Oxygen availability, load and exposure duration influence the aging mechanism.

A credible approval plan compares original properties with aged results and defines acceptable change. For sealing components, dimensional inspection should be combined with compression behavior and an assembly leakage test

Molding, Extrusion and Other Production Routes

Once a compound has been selected, the production method determines which geometries, tolerances and surface conditions are practical. A suitable formulation can still produce an unreliable component when the tooling, cure cycle or secondary operations do not match the design

Compression Molding

Compression molding commonly uses premeasured pieces of high-consistency rubber. The uncured compound is placed in a heated mold, compressed into the cavity and held until sufficient crosslinking occurs.

This route is suitable for many:

Gaskets

Grommets

Sealing rings

Diaphragms

Protective boots

Vibration-control components

Low- to medium-volume custom shapes

Material placement, preform weight, mold temperature, pressure and cure time influence cavity filling and dimensional consistency. Poor control may cause short fills, trapped air, excessive flash or uneven cure.

Compression molding can be practical for larger cross-sections and relatively simple tooling. However, complex undercuts, very thin features and tight flash requirements may need a different process or additional trimming

Liquid Injection Molding

Liquid silicone rubber is commonly supplied as two components that are stored separately, accurately metered, mixed and injected into a heated mold. The low initial viscosity allows the formulation to fill small features and complex cavities.

Liquid injection molding can support:

Thin walls

Complex molded geometry

Small precision features

Automated demolding

Insert molding

High production volumes

Components requiring consistent repeatability

Critical controls include mixing ratio, material temperature, injection pressure, venting, mold temperature and cure time. Because the uncured mixture flows easily, poorly controlled parting lines or vents may produce thin flash.

Platinum-cured LSR can also be sensitive to cure inhibition. Certain sulfur-containing substances, amines, organotin compounds, plasticizers or contaminated surfaces may interfere with crosslinking. Incoming materials, mold-release products, inserts and cleaning chemicals should therefore be reviewed before production

High-Consistency Rubber Injection and Transfer Molding

HCR compounds may also be processed by injection or transfer molding. In transfer molding, a measured charge is placed in a chamber and forced through runners into closed cavities. This can improve material distribution around inserts or across multiple cavities compared with basic compression molding.

The production team must account for compound viscosity, runner design, pressure loss, trapped air and material remaining in the transfer system. These factors affect waste, cycle time and dimensional stability.

Extrusion

Extrusion is used to manufacture continuous silicone rubber tubing, profiles,  and  sealing strips. The uncured compound is forced through a die, supported as it exits and then vulcanized through a continuous heating process.

The die opening does not equal the final dimensions. Die swell, shrinkage, line speed, cure temperature, tension and post-curing can change inner diameter, outer diameter, wall thickness and profile geometry.

For silicone tubing, a useful specification normally includes:

Inner diameter

Outer diameter or wall thickness

Permitted concentricity and ovality

Cut length and length tolerance

Surface condition

Color and translucency

Hardness

Bend or kink requirements

Working medium, temperature and pressure

Cleanliness and packaging expectations

Very soft compounds and thin walls may deform during measurement. Inspection methods should define whether dimensions are checked in a free state, on a mandrel or with non-contact equipment

Calendering and Sheeting

Calendering passes the uncured compound through controlled rolls to produce sheet of a defined thickness. The sheet may then be cured, laminated, reinforced, cut or converted into gaskets and other flat components.

Important variables include roll gap, compound temperature, line tension, thickness uniformity and reinforcement position. A gasket cut from sheet does not have the same material flow, edge condition or dimensional behavior as a directly molded par

RTV Casting, Dispensing and Encapsulation

Room-temperature-vulcanizing systems may be poured, dispensed or injected at relatively low pressure. They are used for encapsulation, potting, formed-in-place sealing, prototypes and selected low-volume components.

Mix ratio, degassing, working time, cure depth, humidity and substrate condition can affect the result. Condensation-cure and addition-cure RTV systems should not be treated as interchangeable because their cure mechanisms, by-products and contamination sensitivities differ.

Post-Curing and Secondary Operations

Some formulations require or benefit from post-curing after the main molding or extrusion stage. A controlled heat treatment may complete crosslinking, reduce certain volatile residues and stabilize properties.

Post-curing conditions must be matched to the compound, component thickness and intended application. Excessive time or temperature can change color, hardness or dimensions.

Secondary operations may include:

Flash removal

Cutting to length

Hole punching

Surface treatment

Printing or marking

Adhesive bonding

Cleaning

Inspection

Controlled packaging

Each operation can introduce defects. Cutting may initiate tears, treatment may lose effectiveness during storage, and unsuitable packaging can deform soft components

Process Selection and Control Matrix

Required Product

Practical Starting Process

Main Variables to Control

Evidence Needed

Gasket, grommet or molded seal

Compression, transfer or injection molding

Charge weight, cavity fill, flash, venting, temperature and cure

Dimensional report, visual criteria and functional sealing test

Thin complex component

Liquid injection molding

Mix ratio, injection conditions, venting, mold temperature and cure inhibition

Cavity inspection, flash limit, cure verification and capability data

Silicone rubber tubing

HCR extrusion and continuous vulcanization

Die design, line speed, ID, OD, wall, ovality, tension and cure

Dimensional inspection, bend evaluation and application testing

Continuous profile or cord

Extrusion

Cross-sectional stability, shrinkage, splice control and cut length

Profile measurement and assembly trial

Flat gasket cut from sheet

Calendering followed by cutting

Sheet thickness, reinforcement, cut quality and flatness

Thickness map, edge inspection and compression test

Encapsulation or formed-in-place seal

RTV dispensing or casting

Ratio, mixing, bubbles, working time, cure depth and adhesion

Cure record, void inspection and substrate adhesion test

Part bonded to metal or plastic

Insert molding, overmolding or secondary bonding

Surface cleanliness, treatment, insert temperature and bond geometry

Peel, pull or application-specific bond test

 

Compression molding liquid injection molding extrusion and encapsulation method

Choosing a Suitable Grade

Selecting a silicone grade should begin with the component’s failure risk, not with color, hardness or a general temperature claim. The same polymer family can be formulated for very different purposes, including electrical insulation, conductivity, fuel resistance, flame behavior, low compression set or controlled human contact

1. Define What the Component Must Do

Start with the primary function. A part may need to:

Maintain a static seal

Carry air or fluid

Protect a cable opening

Electrically isolate two surfaces

Absorb movement or vibration

Prevent dust or moisture entry

Connect two fittings

Protect an assembly from heat

Contact food, skin or medical equipment

One component may perform several functions, but the most serious failure should control the initial selection. For example, a tube that remains flexible at high temperature is still unsuitable if its gas permeability causes unacceptable pressure loss

2. Convert Temperature Into an Exposure Profile

Do not select a grade from the maximum temperature alone. Record:

Minimum and maximum operating temperatures

Continuous and peak conditions

Heating and cooling rate

Number of thermal cycles

Time spent at each temperature

Mechanical load during exposure

Contact with air, oil, steam or chemicals

A standard heat-resistant VMQ may suit prolonged exposure within its documented range. A higher-temperature compound may be needed when retention of elongation, sealing force or dielectric performance is required after severe aging.

For low-temperature movement, confirm that the selected formulation remains flexible at startup rather than merely surviving storage

3. Match Hardness to Geometry and Assembly

Hardness should be selected together with wall thickness, compression, insertion method and tolerance stack.

A soft compound can reduce assembly force and conform to uneven surfaces, but it may deform during handling or extrude through a clearance. A harder formulation can improve shape retention while increasing contact force and reducing the ability to absorb dimensional variation.

For a grommet, review panel thickness, groove dimensions, cable diameter and insertion force. For a gasket, calculate available compression and confirm that the joint can maintain load. Tubing selection should include wall stability, bend radius, connection retention and resistance to kinking

4. Identify the Exact Contact Media

List every liquid, gas, cleaning agent, lubricant and process chemical that may contact the component. Include incidental exposure during assembly and maintenance.

Standard VMQ should not be approved for fuel or solvent service based only on heat resistance. Where petroleum fuels or hydrocarbon oils dominate the risk, fluorosilicone may provide better resistance while retaining useful low-temperature behavior. Its mechanical, permeability and cost implications must still be reviewed.

Hot water and steam also need separate evaluation. A grade that performs well in dry heat may behave differently under prolonged hydrothermal exposure

5. Choose the Required Functional Formulation

The base polymer does not define all functional behavior. Depending on the project, the compound may need to be:

High-tear: for thin lips, pierced features, difficult demolding or stretched assembly

Low-compression-set: for static sealing and long-term contact-pressure retention

Electrically insulating: for barriers, connector seals or protective components

Electrically conductive: for grounding, static dissipation or electromagnetic shielding

Thermally conductive: for heat-transfer interfaces

Flame-retardant: for applications with defined flammability requirements

Low-volatility: for optical, electronic or contamination-sensitive assemblies

Metal detectable: for selected food-processing environments

Self-bonding or adhesion-modified: for overmolding onto a validated substrate

Fluorosilicone: for improved resistance to fuels and selected hydrocarbon fluids

Some requirements conflict. Conductive fillers can reduce electrical insulation, high filler loading may change flexibility, and flame-retardant additives may alter color or mechanical behavior. Prioritize requirements instead of requesting every special property in one formulation

6. Review Cure Chemistry

Peroxide-cured and addition-cured silicone compounds may differ in processing, residual by-products, post-curing needs and contact suitability.

Platinum-cured systems are often considered when cleanliness, low odor, transparency or controlled-contact requirements are important. They can be sensitive to catalyst poisons introduced by incompatible materials or contaminated equipment.

Peroxide-cured compounds can be practical for many molding and extrusion processes, but the selected cure agent and post-cure schedule may affect odor, volatiles, color and final properties.

The drawing should not specify a cure system without a functional reason. Instead, define the required performance and regulatory evidence, then evaluate whether the proposed chemistry can meet it.

7. Separate Color From Material Performance

Color is not proof of grade or compliance. A translucent component is not automatically food-contact or medical grade, and a red-orange product is not automatically suitable for elevated temperature.

Pigments may affect optical appearance, traceability and, in some formulations, electrical or mechanical behavior. Define an approved color reference and tolerance if appearance is important, but qualify the material through documentation and testing

8. Confirm Regulatory and Contact Requirements

For controlled applications, specify the exact destination market and applicable requirement. Examples may include:

FDA requirements for repeated-use rubber articles

EU food-contact rules

BfR recommendations

USP Class VI

ISO 10993 biological evaluation

UL flammability or electrical recognition

Customer-restricted substance lists

RoHS or REACH documentation

9. Approve the Combination, Not Just the Grade

Final approval should cover the compound, production method, cure condition, geometry and relevant secondary operations. A material test slab may confirm basic physical properties but cannot demonstrate tube dimensions, molded flash, bond strength, assembly behavior or leakage performance.

If any of these elements change after approval, the supplier and customer should assess whether revalidation is required

Illustrative Tubing Selection Workflow

Consider an electrical-equipment OEM developing a sensor assembly near a heated enclosure. The initial drawing specifies only:

> Silicone tube, translucent, 50 Shore A.

This description identifies a product family and approximate hardness, but it does not provide enough information for reliable material selection, quotation or validation.

The following example is illustrative. It demonstrates an engineering workflow and should not be presented as a completed customer case without approved project records

Step 1: Identify the Tube’s Actual Function

The tube is not carrying liquid. It covers and electrically separates a sensor lead while protecting it from contact with a warm metal housing.

Its main functions are therefore:

Electrical isolation

Protection from incidental contact

Flexibility during assembly

Dimensional retention around the lead

Resistance to repeated temperature exposure

Because it is not a pressure line, burst strength is not the primary decision factor. Dielectric behavior, wall consistency, bending and heat aging are more relevan

Step 2: Replace General Requirements With Measurable Conditions

The OEM defines the operating profile as:

Continuous temperature: 180°C

Peak temperature: 230°C for up to 10 minutes

Minimum startup temperature: -40°C

No continuous oil or fuel exposure

Occasional contact with assembly cleaner

Required inner diameter: 5.0 mm

Required outer diameter: 8.0 mm

Tight bend near the sensor body

No visible collapse after installation

Electrical insulation required after thermal aging

These conditions create a more useful basis for selecting the compound and extrusion process

Step 3: Identify the Main Failure Risks

The engineering review identifies five possible problems:

Wall variation could create a thin area with reduced electrical protection.

Excessive softness could allow the tube to flatten at the bend.

An unsuitable high-temperature grade could harden after repeated exposure.

Poorly controlled extrusion could produce unacceptable ovality or ID variation.

Cleaning-agent residue could affect the surface or migrate into the assembly.

This step prevents the project from focusing only on Shore hardness

Step 4: Define a Candidate Material and Process

A practical starting point would be an extrusion-grade, electrically insulating VMQ compound with documented heat-aging behavior. The final hardness should be selected after checking flexibility, wall stability and assembly force rather than automatically accepting 50 Shore A.

The proposed production route would include:

Controlled HCR extrusion

Continuous vulcanization

Post-curing when required by the approved formulation

Cut-to-length processing

Dimensional inspection in a defined measurement condition

Clean packaging suitable for the assembly environment

This is a candidate route, not an approved specification. The compound supplier’s technical data and representative samples must support the decision

Step 5: Convert the Drawing Into a Functional Specification

The revised drawing should define:

Material family and approved compound reference

Cure system when functionally necessary

Shore A hardness and tolerance

Inner diameter, outer diameter and wall thickness

Applicable dimensional tolerance

Ovality and concentricity limits

Cut length and end condition

Color or translucency standard

Surface-defect criteria

Bend or kink test

Thermal-aging condition

Electrical acceptance test

Cleanliness and packaging requirements

Change-control expectations

For silicone tubing within an approved size and hardness range, a general dimensional tolerance of ±0.15 mm may be used as a practical production starting point. Where the assembly requires closer control, selected dimensions may be held to approximately ±0.05 mm, subject to manufacturing-feasibility review and an agreed inspection method.

The tighter value should not be applied automatically to every ID, OD, wall thickness or cut length. Very soft compounds, thin walls, large diameters and unsupported measurements can increase apparent variation. The drawing should identify which dimension requires the strict tolerance and how it will be measured

Step 6: Validate Representative Samples

Samples should be produced with the intended compound, die design, vulcanization route and post-cure condition. Testing a hand-made tube or substitute grade may confirm approximate fit but cannot validate production performance.

The dimensional inspection plan should state:

Whether ±0.15 mm or ±0.05 mm applies

Which characteristic the tolerance controls

Measurement temperature

Conditioning time before inspection

Free-state, mandrel-supported or non-contact measurement

Number and location of measurement points

Treatment of ovality and concentricity

Gauge resolution and calibration status

For a tube specified at 5.0 mm ID and 8.0 mm OD, a general tolerance could initially be written as:

ID: 5.0 ± 0.15 mm

OD: 8.0 ± 0.15 mm

If assembly testing shows that one interface requires tighter control, that critical dimension may be revised to ±0.05 mm after process-capability confirmation. The other dimensions do not need to receive the same strict tolerance unless their functional effect justifies it.

The remaining validation plan should include:

Wall-thickness measurements

Ovality and concentricity assessment

Bend test at the minimum installation radius

Assembly trial with the actual lead and housing

Heat aging at a defined time and temperature

Hardness and elongation comparison before and after aging

Dielectric strength or application-specific electrical testing

Visual inspection for cracks, surface defects and discoloration

Evaluation after contact with the assembly cleane

Step 7: Establish Production Controls

After sample approval, the control plan should link the accepted requirements to production records. Depending on risk, controls may include incoming compound identification, extrusion dimensions, cure settings, post-cure batch records, cut length, visual inspection and packaging verification.

Any change to compound, catalyst, production line, die, cure condition or secondary operation should be reviewed for its effect on the approved results.

Commercial Action Path

This example creates a complete buyer journey:

Begin with the component function.

Document the operating conditions.

Identify the likely failure modes.

Select a candidate formulation and production route.

Convert those decisions into drawing requirements.

Produce representative samples.

Validate the tube in the actual assembly.

Approve production controls and change management.

Release the purchase specification.

The process turns the vague phrase “silicone tube” into a controllable component specification without assuming that every silicone formulation performs in the same way.

Translucent silicone tubing protecting a sensor lead near heated electrical equipment

Tests, Reports and Approval Records

Validation should prove that the delivered component performs as intended, not merely that the raw compound matches a generic silicone datasheet. Material properties, production records, dimensional inspection and application testing provide different types of evidence.

1. Material Technical Datasheet

A technical datasheet describes typical properties of a commercial compound. It may include hardness, tensile strength, elongation, tear strength, density, cure conditions and electrical values.

These figures are useful for screening, but they are normally typical rather than guaranteed lot results. They may also come from standard test slabs rather than the manufactured component

2. Batch Certificate or Certificate of Analysis

A certificate of analysis links selected test results to a production batch. It should identify:

Compound name or internal material code

Batch or lot number

Manufacturing or release date

Tested characteristics

Test method

Specification limits

Actual results

Approval status

3. Finished-Part Inspection Report

This report verifies characteristics created or influenced by manufacturing. Depending on the product, it may include:

ID, OD, wall thickness and cut length

Molded dimensions

Ovality and concentricity

Flash and parting-line condition

Surface defects

Color

Weight

Hardness

Post-cure status

Packaging condition

4. Application Validation

Application testing evaluates the component in a representative assembly and environment. It may assess leakage, pressure retention, bending, insertion force, electrical isolation, thermal cycling, fluid exposure or long-term compression.

This is the strongest evidence of suitability because it includes the effects of geometry, interfaces and actual loading. It does not eliminate production inspection; both are needed for controlled release.

Test Methods and What They Prove

Characteristic

Common Reference Method

What the Result Indicates

Important Limitation

Shore A hardness

ASTM D2240 or ISO 48-4

Resistance to indentation under defined conditions

Does not directly predict modulus, sealing force or compression set

Tensile strength and elongation

ASTM D412 or ISO 37

Behavior of a standardized specimen under tension

Results depend on specimen shape, extension rate, temperature and conditioning

Tear strength

ASTM D624 or ISO 34-1

Resistance to propagation of a defined cut or notch

Different die geometries can produce non-equivalent results

Compression set

ASTM D395 or ISO 815-1

Permanent deformation after controlled compression and recovery

Test temperature, time, deflection and method must be reported

Heat aging

ASTM D573 or ISO 188

Change in selected properties after hot-air exposure

Does not automatically reproduce load, fluid contact or oxygen conditions in service

Fluid immersion

ASTM D471 or ISO 1817

Changes in volume, mass, hardness and mechanical properties after fluid exposure

The actual fluid, concentration, time and temperature must match the project

Dielectric strength

ASTM D149 or IEC 60243-1

Breakdown strength through a solid insulating specimen

Strongly influenced by thickness, electrodes, voltage rate and surrounding medium

Volume resistivity

ASTM D257 or IEC 62631-3-1

Resistance to current flow through the material

Contamination, humidity, specimen preparation and conditioning affect results

Flammability

UL 94 or an application-specific standard

Burning behavior under a defined laboratory configuration

A material rating does not automatically certify the finished product

Dimensional inspection

Approved drawing and agreed measurement procedure

Conformance of the delivered geometry

Soft or curved parts can deform under measurement force

Hardness Testing on Finished Components

A Shore A reading requires sufficient material thickness and a suitable measurement surface. Thin tubing walls, curved profiles and small molded features may not provide a valid test location.

Possible approaches include:

Testing a standard plaque cured with the production batch

Stacking permitted specimens when the method allows it

Using a micro-hardness method for small sections

Recording hardness as a compound-control result rather than a direct tube-wall measurement

The inspection plan should state where and how hardness is measured. A reading taken on an unsupported curved wall should not be compared directly with a flat laboratory plaque

Thermal-Aging Evidence

A useful heat-aging report should show both original and aged results. Relevant changes may include:

Hardness change in Shore A points

Percentage change in tensile strength

Percentage change in elongation

Change in tear strength

Dimensional movement

Compression-set result

Surface cracks, tack, discoloration or deformation

The report should identify exposure temperature, duration, air circulation, specimen condition and recovery time before measurement.

Testing at 240°C for a few hours cannot independently establish multi-year service life. Accelerated aging requires an appropriate model and more than one exposure condition if the result will be used for life prediction.

Compression-Set Reporting

A compression-set value is incomplete unless the report includes the method, temperature, duration, compression level and recovery condition.

ASTM D395 includes different methods for constant force and constant deflection. Its primary relevance is rubber exposed to compressive stress, particularly in static service.ASTM D39

Electrical Test Evidence

Electrical reports require more detail than a single dielectric-strength value. For ASTM D149 testing, the specimen preparation, conditioning, surrounding medium, electrode configuration, voltage application and failure criterion can affect the result.ASTM D149 (https://store.astm.org/standards/d149)

For an insulating silicone component, the validation plan may need to include:

Dielectric strength

Volume resistivity

Insulation resistance

Tracking or erosion resistance

Arc or corona exposure

Performance after heat aging

Performance after humidity or fluid exposure

Creepage and clearance in the finished assembly

A high material value cannot compensate for an air gap, thin wall, contamination path or unsuitable component geometry

Dimensional Measurement for Soft Tubing

Silicone tubing can deform under gauge pressure. The report should define whether dimensions are measured:

In the free state

On a specified mandrel

With an optical or non-contact system

At defined positions around the circumference

Before or after post-curing

After a stated conditioning period

For the tubing example in Module 09, the inspection record should distinguish the normal ±0.15 mm tolerance from any critical dimension approved at ±0.05 mm. The stricter limit requires suitable gauge resolution and verified process capability

Minimum Contents of an Approval Report

A complete approval record should contain:

Drawing number and revision

Material or compound identification

Batch number

Production method

Cure and post-cure condition

Sample quantity

Test methods

Test conditions

Acceptance limits

Actual measured results

Equipment identification or calibration status

Deviations

Photographs where useful

Reviewer and approval status

Traceability to retained samples or production batch

Statements such as “tested,” “high-temperature resistant” or “meets electrical requirements” are not adequate without conditions and measured results

Industrial Uses and Their Critical Proof

Silicone appears in many industries, but its role changes with the application. A tubing specification, electrical insulator and static gasket should not use the same approval criteria merely because they share the same base polymer family

Electrical and Electronic Equipment

Silicone rubber is used where electrical insulation must coexist with temperature variation, moisture or mechanical movement. Typical product forms include:

Connector seals

Cable-entry grommets

Insulating boots

Wire and sensor protection tubing

Keypads and flexible switching elements

Potting and encapsulation systems

High-voltage insulator components

Thermal-interface pads

For these applications, a project may need to control dielectric strength, volume resistivity, tracking resistance, flame behavior, wall thickness and contamination. Conductive or thermally conductive grades should be treated separately from insulating compounds.

An electrically insulating formulation may fail after assembly if a thin section, surface deposit or inadequate creepage path creates a local weakness. Validation should therefore include the finished geometry and surrounding hardware

Industrial Sealing

Silicone is used for static seals exposed to heat, weather or repeated temperature cycling. Examples include:

Flat gaskets

Molded sealing rings

Enclosure seals

Oven and heater seals

Lighting-system gaskets

Access-panel seals

Protective dust and moisture barriers

The design should define compression, flange condition, fastener load, surface finish and permitted leakage. High-temperature capability alone does not ensure long-term sealing. Compression set, stress relaxation and joint movement may control service life.

For dynamic sliding or heavily abrasive service, another elastomer may be more suitable unless a validated design addresses friction and wear.

Silicone Rubber Tubing

Extruded tubing can be used for air, water, drainage, laboratory transfer, equipment connections and protective sleeving. Selection should begin with the actual function because a tube carrying fluid has different requirements from one used only as an insulating cover.

Relevant design inputs include:

ID, OD and wall thickness

Pressure or vacuum

Fluid or gas identity

Continuous and peak temperature

Bend radius

Kink resistance

Connection method

Pull-off force

Gas and vapor permeability

Cleanliness

Sterilization or washing conditions

Cut length and packaging

The general ±0.15 mm dimensional tolerance and the stricter ±0.05 mm capability discussed earlier should be assigned only after reviewing size, hardness, wall geometry and measurement conditions.

When pressure is involved, working pressure should not be inferred from wall thickness alone. Compound strength, diameter, temperature, fittings, safety factor and aging condition all affect the result

Food and Beverage Equipment

Selected silicone grades are used in processing, dispensing, filling and sealing equipment because they can be formulated for repeated-use food-contact applications and cleaned under controlled conditions.

Possible components include:

Transfer tubing

Filling-machine seals

Door and access gaskets

Flexible connectors

Dispensing valves

Protective covers

Approval should identify the destination market, applicable food-contact regulation, colorant status, cure condition and cleaning process. A declaration for the raw compound does not automatically establish compliance of the finished product.

The project should also consider whether the component can trap product, absorb cleaning chemicals or release particles during repeated assembly.

Healthcare and Laboratory Equipment

Silicone elastomers can be used in selected respiratory, diagnostic, laboratory and fluid-management equipment. Their flexibility, transparency options and broad temperature behavior can be useful, but “medical-grade silicone” is not a complete specification.

Depending on the intended contact, the project may need:

Biological evaluation

Extractables and leachables assessment

Sterilization compatibility

Particulate and cleanliness controls

Traceability

Change notification

Controlled manufacturing environment

Finished-device risk assessment

Transportation and Mobility

In vehicles, rail equipment and other transportation systems, silicone components may encounter heat, vibration, outdoor weathering and electrical exposure. Product forms can include:

Sensor and connector seals

Lighting gaskets

Battery-system protection

Cable boots

Thermal-management components

High-temperature tubing

Vibration-isolation parts

Engine oil, fuel, coolant, brake fluid and cleaning chemicals must be identified separately. Standard VMQ should not be selected for an under-hood application solely because its temperature rating is acceptable.

For fuel or oil exposure, fluorosilicone or another elastomer may be more appropriate after compatibility and mechanical review.

Heating and Process Equipment

Silicone seals and profiles can be used around ovens, heaters, drying systems and other equipment exposed to elevated temperature.

Important design variables include:

Continuous temperature

Radiant versus conducted heat

Thermal cycling

Joint movement

Compression level

Airflow

Oxidation

Cleaning chemicals

Required replacement interval

Application-to-Evidence Principle

The material name identifies a possible starting point. The application determines which evidence is relevant.

For example:

Electrical protection requires dielectric and geometry evidence.

Static sealing requires compression and leakage evidence.

Fluid transfer requires compatibility, pressure and cleanliness evidence.

Outdoor service requires aging and wet-performance evidence.

Controlled contact requires regulatory and traceability evidence.

This distinction prevents one generic silicone datasheet from being used to approve unrelated component

Industrial tubing gasket grommet and high temperature profile application

What to Send With an RFQ

Send the latest drawing, part function, critical dimensions, measurement method, service profile, every contact medium, mandatory performance limits, destination-market requirements, sample plan and expected annual volume. For tubing, add ID, OD, wall, cut length, ovality, bend radius, connection, pressure or vacuum, cleanliness and packaging. For molded seals, add groove or flange data, compression, fastener load, surface condition, leakage limit and flash location. Separate essential limits from preferences and identify which dimensions need tighter control. Name the required certificate or report instead of requesting generic compliance

1. Part Identity and Function

State what the component does in the assembly.

Include:

Part name and number

Drawing revision

Primary function

Location in the assembly

Consequence of failure

Existing problem or reason for development

Prototype, replacement or new-production status

“Silicone gasket” is not a sufficient function. Explain whether it prevents water entry, contains air pressure, electrically isolates a housing or protects against dust.

2. Drawing and Geometry

Provide a dimensioned drawing whenever possible. A sample can support evaluation, but it should not replace the original design information.

The drawing should identify:

Critical and noncritical dimensions

Datum structure

General tolerances

Any dimensions requiring ±0.05 mm control

Dimensions using the normal ±0.15 mm starting tolerance

Surface finish where relevant

Flash and parting-line limits

Radii and permitted edge conditions

Color and appearance

Marking requirements

For soft tubing or flexible profiles, also define the measurement condition. The manufacturer needs to know whether dimensions are measured freely, on a mandrel or with non-contact equipment.

3. Service Environment

Describe the complete operating profile rather than providing only the maximum temperature.

Include:

Minimum, continuous and peak temperatures

Duration of peak exposure

Thermal-cycle frequency

Indoor or outdoor use

UV, ozone and weather exposure

Pressure or vacuum

Static or dynamic movement

Compression or stretching

Vibration

Expected service life

Maintenance or replacement interval

When the local component temperature is unknown, identify the nearest heat source and provide available assembly measurements.

4. Contact Media

List each material that may contact the component during manufacturing, assembly, operation, cleaning and maintenance.

Examples include:

Air or process gases

Water

Steam

Oils and greases

Fuel

Coolant

Solvents

Cleaning chemicals

Adhesives

Mold-release agents

Adjacent plastics or coatings

Use the exact trade name, chemical composition or safety-data information when available. General descriptions such as “oil resistant” or “chemical resistant” are not sufficient for compatibility review.

5. Material and Performance Requirements

If a silicone grade has already been approved, provide the exact compound reference and revision. If the material remains open, define the required performance instead of selecting a grade from color or appearance.

Possible requirements include:

Shore A hardness

Tensile and elongation limits

Tear resistance

Compression set

Heat-aging retention

Low-temperature flexibility

Fluid-immersion limits

Dielectric strength

Volume resistivity

Flame classification

Tracking or arc resistance

Gas-permeability limit

Low-volatility requirement

Color stability

Bond strength

Separate mandatory requirements from preferences. An unnecessarily restrictive specification can reduce available manufacturing options without improving function.

6. Product-Specific Inputs

For Silicone Tubing

Provide:

ID, OD and wall thickness

Cut length

Concentricity or ovality requirement

Minimum bend radius

Kink limit

Working and burst pressure where applicable

Vacuum requirement

Connection type

Pull-off force

Flow requirement

Permeability limit

Cleanliness and packaging

For Molded Seals and Gaskets

Provide:

Groove or flange dimensions

Compression target

Mating-surface condition

Fastener or clamp load

Permitted leakage

Assembly lubricant

Flash location

Parting-line restrictions

Installation method

Reuse requirement

For Grommets and Protective Components

Provide:

Panel thickness

Hole diameter

Groove dimensions

Cable or shaft diameter

Installation direction

Insertion and retention force

Edge condition

Movement after assembly

7. Regulatory and Documentation Requirements

Identify the destination market and required evidence before quotation.

This may include:

Food-contact declaration

Medical or biological evaluation

RoHS and REACH documentation

Restricted-substance declaration

UL recognition or flammability data

Material traceability

Certificate of analysis

First-article inspection report

Production inspection report

Change-notification requirement

Retention period for batch records or samples

Do not request a generic “compliance certificate.” Name the regulation, standard, customer specification or required document.

8. Validation Requirements

Define who will perform each test, who pays for it and what constitutes approval.

Clarify:

Sample quantity

Prototype tooling or production tooling

Test methods

Test conditions

Acceptance limits

Required report format

Customer assembly trial

Responsibility for regulatory testing

Approval authority

Revalidation triggers

If the initial samples use substitute tooling, compound or processing conditions, the report should identify those differences.

9. Commercial and Supply Information

A technically suitable quotation also depends on production and supply expectations.

Provide:

Estimated annual quantity

Order quantity or release schedule

Prototype quantity

Target production date

Packaging quantity

Labeling format

Shelf-life requirement

Delivery destination

Forecast variability

Spare-parts demand

Tool ownership requirement

Annual volume can influence the preferred molding route, cavity count, automation level and tooling investment.

Practical Questions You Still Ask

Is silicone rubber a thermoset or a thermoplastic?

Most cured products are thermoset elastomers. Crosslinking creates a permanent network, so the finished article cannot normally be remelted and molded again like a conventional thermoplastic.

No. It is synthetic and is not made from natural rubber latex. If natural rubber is prohibited, obtain a declaration covering adhesives, coatings, processing aids, packaging and other assembly materials as well.

It cannot normally be remelted. Some clean scrap may be ground as filler or handled through specialized chemical recovery, subject to cure chemistry, contamination, volume and local infrastructure.

Odor may come from cure by-products, cleaning agents, packaging or insufficient post-cure. It neither identifies the exact grade nor proves noncompliance. Odor-sensitive projects need an agreed process and evaluation method

Keep uncured systems sealed within the supplier’s temperature and shelf-life limits. Protect finished articles from heat, sunlight, contamination and deformation; do not compress or sharply bend soft tubing during storag

Some grades tolerate repeated steam, ethylene oxide or radiation cycles, but compatibility is not universal. Validate the exact method, dose or temperature, cycle count, packaging and finished geometry.

FTIR can often identify the polymer family, while other tests estimate hardness, filler or thermal behavior. Analysis may not reveal the commercial grade, additive package, cure history or original dimensions

No. Concentrated or high-pressure oxygen requires dedicated compatibility, ignition-risk and cleanliness assessment. Formulation, residues, particles, pressure, temperature and flow all matter

Is Silicone the Right Choice for Your Design?

Silicone is a strong candidate when temperature stability, electrical insulation or weather resistance outweighs abrasion, fuel exposure and gas permeability. Match the compound, geometry and production method to measurable risks, then validate representative parts. Submit your drawing and service conditions for an engineering review

"Take The Efficient Booster For Your Business Now "

Alan Chen

Product Sales Manager & Rubber Specialist at RISEUP

Please enable JavaScript in your browser to complete this form.

Related Articles

032806.png

Hey!
I’m Alan, Product Sales Manager at RISEUP. I’ve been working in the rubber industry  for over 20 years. I’m happy to share my industry knowledge with you. If you have any questions I’d be happy to help.

Get A Quick Quote
Please enable JavaScript in your browser to complete this form.